Audi RS5 B10 Avant lowered on H&R height adjustable springs with TRAK+ spacers, side on
Performance · November 2026
Workshop build

Audi RS5 B10 Avant, lowered on H&R springs and TRAK+ spacers.

Height adjustable springs on the factory dampers, spacers front and rear, fitted and aligned in our Sydney workshop. Every part is listed below with its price.

B10Audi RS5 Type B10 Avant
25 to 35 mmFront drop range, H&R VSS
25 to 40 mmRear drop range, H&R VSS
12 / 10 mmSpacers per side, front / rear
$4,354Package, fitted and aligned

Before and after

Audi RS5 B10 Avant, before and after

Audi RS5 B10 Avant at factory ride height before lowering, side on
Before. Factory height, factory offset.01
Audi RS5 B10 Avant lowered on H&R height adjustable springs with TRAK+ spacers, side on
After. H&R VSS height adjustable springs, TRAK+ spacers, wheel alignment02
Front wheel arch gap on the Audi RS5 B10 Avant before lowering
Front, before
Front wheel of the Audi RS5 B10 Avant after H&R springs and 12 mm TRAK+ spacers
Front, after
Rear wheel arch gap on the Audi RS5 B10 Avant before lowering
Rear, before
Rear wheel of the Audi RS5 B10 Avant after H&R springs and 10 mm TRAK+ spacers
Rear, after

What went on the car

Parts fitted to this Audi RS5 B10 Avant

Two parts, each linked below with its price. Buy them one at a time, or as the package with fitting included.

Why these parts

Why H&R height adjustable springs and TRAK+ spacers suit the RS5 B10

Rear wheel of the Audi RS5 B10 Avant after H&R springs and 10 mm TRAK+ spacers

Springs, not coilovers. The factory dampers on the B10 are good, so the H&R VSS kit keeps them and replaces only the springs with height adjustable units. You get a drop you can set, 25 to 35 mm at the front and 25 to 40 mm at the rear, and a ride that stays close to standard.

Spacers to finish the stance. Lowering on its own leaves the wheels tucked in. TRAK+ spacers push the factory 21s out by 12 mm a side at the front and 10 mm at the rear, which is H&R's own recommendation for this car on standard wheels and tyres. The extended bolts come with the kit, matched to each axle.

Set up, not just bolted on. Springs and spacers fitted, heights set on the car to suit the owner, then a full wheel alignment before it left. One day in the workshop. If your RS5 is on aftermarket wheels or a different offset, talk to us before ordering and we will size the spacers for your setup.

Questions

Audi RS5 B10 Avant, the questions we get asked

How low does the RS5 B10 Avant go on H&R VSS springs?

Between 25 and 35 mm at the front and 25 and 40 mm at the rear. The height is set on the car, so you choose where in that range it sits.

Do the TRAK+ spacers fit the factory 21 inch wheels?

Yes. 12 mm per side front and 10 mm rear is H&R's tested sizing for the B10 Avant on standard wheels and tyres. Other wheels or offsets need a different size, so ask first.

Does lowering on springs change the ride?

Less than coilovers would. The dampers are factory, so the car rides close to standard with a firmer edge from the shorter spring.

Will this kit fit an earlier RS5?

No. This kit is for the Type B10. The earlier F5 and 8T use different part numbers, and we have packages for those too.

How long is the car in the workshop?

One day. Springs, spacers, bolts and a wheel alignment, with the heights set before it leaves.

Enquire

Talk to us about your car

Tell us what you drive and what you have in mind. We come back with a plan and a price, usually the same day.

463 Princes Highway, Sydenham NSW Mon to Fri, 9:00am to 5:30pm (02) 9557 3739
Heasmans collects these details to respond to your enquiry.

More builds

More cars out of the Heasmans workshop

All builds →